How To Install Interconnected Smoke Alarms

Ways to interlink alarms*

FireAngel Smart RF provides flexible wireless solutions for both hard-wired and battery systems. Up to 50 fume, rut or carbon monoxide alarms tin can be interlinked in a network for maximum coverage.

There are 3 master ways to interlink FireAngel Specification smoke alarms:

1. Hardwired interlinked
2. Interlinked via wireless radio-frequency (Smart RF Interlink)
3. Mixed systems – a hybrid system of difficult-wired and Smart RF. This provides contractors with system flexibility. Additional fume, estrus, CO and specialised products such as strobes and pads and low frequency sounders for the deaf and hard of hearing tin easily exist wirelessly added or removed.

Interlinking alarms via Smart RF

FireAngel Smart RF enabled alarms are connected via Intelligent Radio Frequency (RF) applied science. Smart RF simplifies installation as alarms can exist linked together in a matter of seconds via a two button press "learning in" process.

It is important to notation, that unique identity codes (16 million unlike combinations) are hard coded into the memory of the fire alarm network upon interlinking and then these will exist retained fifty-fifty if the mains is turned off.

Features of Smart RF

1. Each Smart RF alarm constantly monitors and communicates with other alarms in the network
2. Mimics the sound blueprint of the activated alarm – when an alert detects smoke, heat or carbon monoxide all alarms in the network will mimic the sound pattern of the trigger alarm.

Tailored to adapt the needs of the property and tenant:

1. Test and locate from anywhere in the domicile with an alert control unit. This can exist added to any Smart RF network.
2. Boosted smoke, heat, CO and accessories for the deaf and hard of hearing can exist added or removed at someday.
3. Smart Silence – allows the user to silence the activating alert for up to ten minutes in the event of a known simulated alarm. After x minutes the alarm shall return to full sensitivity
4. Locate feature – when the network goes into warning pressing the test button of any warning will silence all only the initiating alert.
5. Sleep Like shooting fish in a barrel – A depression bombardment 'chirp' can exist silenced for a period of 8 hours by pressing the exam button

FireAngel Smart RF smoke alarms (including the FireAngel Specification range) use Multi-Sensor technology used by over xc% of the Fire and Rescue Service. To discover out more nearly our technologies and products bachelor, please see the FireAngel product guide.

Hardwired and wireless interconnected smoke alarms

FireAngel has mixed system capability, allowing for the interlinking of battery and mains alarms.

Merely i mains powered Smart RF enabled warning is required to adapt an established hardwired interconnected organisation to communicate to other FireAngel wireless products. It as well allows you to connect split up hardwire, interconnected networks, into one network past adding just i Smart RF enabled warning to each section.

Time and cost saving advantages of wireless alarms

Equally Smart RF interlinks alarms via radio-frequency, you do not need to feed the wiring from one alarm to some other. This can be a very time consuming procedure, and can cause problems with tenants non wanting trunking running up walls and across ceilings. In that location is no need to lift floorboards either. As a event, your harm claims to floors, carpets and decoration are minimised – if non eliminated.

As wireless alarms are more than expensive, it is easier to justify the additional price when retro-fitting fume alarms as this is where surface trunking is often used.

In new build backdrop, cable can be relatively cheap and like shooting fish in a barrel to install (without the need for trunking) so the extra price may not be a feasible proffer to you. Yet, some new build backdrop have concrete ceilings, significant that surface wiring via trunking will yet be necessary. In these applications the utilize of RF will probable to be highly beneficial.

To connect Smart RF alarms onto an existing, hardwire network

Existing hardwire interconnect between all alarms in the domicile.

Place one mains powered Smart RF enabled smoke or rut alarm on the existing hard-wired network. This volition link all other Smart RF alarms or accessories to communicate to hardwire interconnected alarms.

To connect Smart RF alarms as split up hardwired fire alarm systems

Dissever hardwire interconnected networks in the dwelling.

To wirelessly link separately hardwire interconnected networks, such as upstairs and downstairs:

Identify one mains powered Smart RF enabled alarm on each hardwire interconnected network, to wirelessly link the networks together.

YOU SHOULD NEVER:
• Exceed 250m of connecting wire per circuit.
• Connect FireAngel alarms to any other models produced by some other manufacturer.

Useful resources for electricians installing smoke detectors

• Electrical Contractors eBook

Installing hardwired and wireless fume alarms to meet Building Regulations

• Your Guide For Fume Warning Positioning To Meet Building Regulations

Source: https://www.fireangel.co.uk/how-to-install-hardwire-and-wireless-smoke-alarms-in-a-mixed-system/

Posted by: iglesiascocam1971.blogspot.com

Share this post